![ricoh mpc2551 error code j001 ricoh mpc2551 error code j001](https://i.ytimg.com/vi/STOLPVdB7Qg/maxresdefault.jpg)
- RICOH MPC2551 ERROR CODE J001 MANUALS
- RICOH MPC2551 ERROR CODE J001 DRIVER
- RICOH MPC2551 ERROR CODE J001 SERIES
SC636Ĝommunication Error Between BICU & Paper Feed Control PWA SC600Ĝommunication Error Between Main Control and Operation Panel Boards Too much dust in the fan causing too much load on the motor driver. Loose connection of the exhaust fan motor. Machine is plugged into low line voltage.įixing thermistor is defective or out of position. Main motor or its driving board is defective.īefore replacing motors or sensors, first check the mechanical load. Some gears or other rotating parting has been jammed. SC500:Too much load on the drive mechanism SC590Ğxhaust/Fusing fan motor error/used toner collection motor error SC557 Pressure roller temperature does not increase SC555 Pressure roller ready temperature abnormal SC554 Pressure roller low temperature abnormal SC547 Zero cross signal malfunction/ Fusing temperature does not increase SC544 Hot roller fusing lamp lower limit temperature detected SC541ğuser thermistor open/ Hot Roller thermistor open SC531ğuser/Duplexer reversing motor error SC530ěypass feed motor lock/fusing fan motor error
RICOH MPC2551 ERROR CODE J001 DRIVER
SC521ĝuplexer jogger driver motor error 2 SC520 Paper tray error/Duplexer jogger drive motor error SC515ĝrawer left guide drive motor error, Tandem rear fence motor error SC504ĝrawer 4 or 3rd lift motor malfunction SC502Ēnd or 1st tray lift motor malfunction SC500 Main motor/transport motor lock/Fusing motor error
RICOH MPC2551 ERROR CODE J001 SERIES
(d) 5xx Series For Paper Feed and Fusing Problems SC392:Toner density sensor initial setting is not performed correctly.ĭevelopment roller coupling gear is not correctly attached. Transfer Bias Paper Attraction Roller Bias Leak Image Transfer Belt Cleaning Unit Position Error (c) 3xx and 4xx Series Image Development Problems. In some models (AF 2015 etc) 2xx error series does not exist. The firmware program of the engine and the controller do no match. SC143:SBU white/black level correction error: SC 192Ěutomated SBU adjustment error/Bar code number is differentĬheck exposure lamp connections and the stabilizer board.ĭirty scanner mirror or scanner mirror out of positions. SC 173 Scanner Lamp regulator adjustment error SC 170 Scanner DA1 Abnormal/Video processing Sc 130 SBU defective error/ Scanner start abnormal SC 127 Scanner motor encoder rotating direction error Sc 124 Scanner Motor encoder signal error Each category starts with a unique number starting from 1 to9. Ricoh error codes are generally categorized into 9 categories. It is strongly recommended to call an authorized technician to reset and fix this problem because defected parts must be replaced/repaired before resetting these errors otherwise it may result in fire or other damages. These errors indicate a problem in fixing temperature or thermistor. SC543, SC545 are most common errors in Ricoh products.
RICOH MPC2551 ERROR CODE J001 MANUALS
Error levels can be checked in service manuals under “troubleshooting” section. The C level errors have no effect on machine operation except to display a warning on the control panel. The machine operates as usual, excluding the related units. The B level errors are caused by one or more specific units. Only a service engineer should reset and repair this error. The “A” level codes have high risk and involve the fusing unit problems.
![ricoh mpc2551 error code j001 ricoh mpc2551 error code j001](https://i.ytimg.com/vi/yhib7TDoRgU/hqdefault.jpg)
That jam code J001 area C at startup which doesn't clear, many times is caused by a bad door switch.Ricoh photocopier/printers error codes can be divided into three levels (A, B,C). Should I remove and test the Inverter sensor? I realize this may be recommended, but as well I'm worried about this not being the real issue.Īnd so, I turn to the forums for help. I notice that the Guide Plate (D039 6221 GUIDE PLATE:TRANSFER UNIT) is also broken where it should hold the pin from the transfer unit (D039 6210 TRANSFER/SEPARATION UNIT:SECOND:ASS'Y) but I'm not convinced this actually has anything to do with the problem, since this shouldn't have any effect or relation to the symptoms above. While checking the machine, on one occasion SC670 is triggered, but on reset and machine restart does not return.
![ricoh mpc2551 error code j001 ricoh mpc2551 error code j001](http://i.ytimg.com/vi/tmuB1fKkXX4/maxresdefault.jpg)
Running SP7-507 reports jam code 064, which implies the Inverter Sensor is shorted somehow. After checking thermistors and noticing the wear, the fuser was replaced with a genuine new fuser from Ricoh.Īlso of note, the gate pawl (D039 4588 GATE PAWL:REVERSE:ASS'Y) was extremely brittle, and easily broke with a light touch to the fins.Īfter finishing up and resetting the PM counter (SP 3902-014 set to 1) the machine was happy, and printing nicely for about a day or two.Īt this point, the machine begins reporting jam code J001 (area C) on startup. I've been working on a Ricoh Aficio MP C2550 for a while.